Warning | ||
---|---|---|
| ||
This page needs to be overworked |
Introduction
Collective attributes are attributes whose values are shared across a collection of entries. It's very common to encounter situations where a bunch of entries have the same value for an attribute. Collective attributes for LDAP are defined in RFC 3671. ApacheDS implements this RFC.
Use Case
For example one might organize everyone in an engineering department under an ou, 'ou=engineering'. If the engineering team is located in the same area and building then several attributes in each user entry within engineering will have the same value. An example of such an attribute would be the locale. If engineering is located in Sunnyvale CA then all locale attributes of entries under 'ou=engineering' would be set to Sunnyvale.
Rather than manage the value for this attribute in each entry a single collective attribute can be used in a subentry. Changes to the value of this attribute would immediately be reflected to those entries selected by the subtreeSpecification of subentry. For more information on specifying subtrees take at Subentries.
Setting up a Collective Attribute Administration Area (AA)
To manage collective attributes for a collection of entries you must add collective subentries to the Administrative Point (AP) of the collective AA. For more information on AAs see Subentries. These collective subentries must have the objectClass subentry as well as collectiveAttributeSubentry. Also the AP, of the AA, must have an administrativeRole value of collectiveAttributeSpecificArea (2.5.23.5) or collectiveAttributeInnerArea (2.5.23.6).
Example
For the use case above we can presume a partition at the namingContext 'dc=example,dc=com' with an 'ou=engineering' entry below containing users from the engineering team in Sunnyvale. Let's presume no AA has yet been defined so we have to create one. We'll set the partition root 'dc=example,dc=com' as the AP of an AA that spans the entire subtree. For this simple example the AA will be autonomous for the collective aspect. Setting this up is just a matter of modifying the 'dc=example,dc=com' entry so it contains the operational attribute administrativeRole with the value collectiveAttributeSpecificArea. The code below sets up this AAA for collective attribute administration.
No Format |
---|
// Get a DirContext on the dc=example,dc=com entry
Hashtable env = new Hashtable();
env.put( "java.naming.factory.initial", "com.sun.jndi.ldap.LdapCtxFactory" );
env.put( "java.naming.provider.url", "ldap://localhost:" + port + "/dc=example,dc=com" );
env.put( "java.naming.security.principal", "uid=admin,ou=system" );
env.put( "java.naming.security.credentials", "secret" );
env.put( "java.naming.security.authentication", "simple" );
ctx = new InitialDirContext( env );
// Modify the entry to make it an AAA for collective attribute administration
Attributes mods = new BasicAttributes( "administrativeRole", "collectiveAttributeSpecificArea", true );
ctx.modifyAttributes( "", DirContext.ADD_ATTRIBUTE, mods );
|
...
No Format |
---|
dn: cn=engineeringLocale,dc=example,dc=com objectClass: top objectClass: subentry objectClass: collectiveAttributeSubentry cn: engineeringLocale c-l: Sunnyvale subtreeSpecification: {base "ou=engineering", minimum 4} |
The following picture present the structure of our tree :
A couple points regarding this subentry's LDIF:
...
Note that the minimum value of 4 is used in the subtreeSpecification to make sure that the entry 'ou=engineering,dc=example,dc=com' does not have c-l: Sunnyvale added to it. It's got 3 components to the DN so minimum 4 chops it out of the collection.
Collective Attribute Types
As one can see from the example above, special collective attributes are used for regular attributes: c-l for l. These attributes are derived from the original attribute and are marked as COLLECTIVE. RFC 3671 defines a bunch of these which are listed below. If you don't find what you're looking for just add it to your own schema using this pattern.
...
No Format |
---|
3.1. Collective Locality Name
The c-l attribute type specifies a locality name for a collection of
entries.
( 2.5.4.7.1 NAME 'c-l'
SUP l COLLECTIVE )
3.2. Collective State or Province Name
The c-st attribute type specifies a state or province name for a
collection of entries.
( 2.5.4.8.1 NAME 'c-st'
SUP st COLLECTIVE )
3.3. Collective Street Address
The c-street attribute type specifies a street address for a
collection of entries.
( 2.5.4.9.1 NAME 'c-street'
SUP street COLLECTIVE )
3.4. Collective Organization Name
The c-o attribute type specifies an organization name for a
collection of entries.
( 2.5.4.10.1 NAME 'c-o'
SUP o COLLECTIVE )
3.5. Collective Organizational Unit Name
The c-ou attribute type specifies an organizational unit name for a
collection of entries.
( 2.5.4.11.1 NAME 'c-ou'
SUP ou COLLECTIVE )
3.6. Collective Postal Address
The c-PostalAddress attribute type specifies a postal address for a
collection of entries.
( 2.5.4.16.1 NAME 'c-PostalAddress'
SUP postalAddress COLLECTIVE )
3.7. Collective Postal Code
The c-PostalCode attribute type specifies a postal code for a
collection of entries.
( 2.5.4.17.1 NAME 'c-PostalCode'
SUP postalCode COLLECTIVE )
3.8. Collective Post Office Box
The c-PostOfficeBox attribute type specifies a post office box for a
collection of entries.
( 2.5.4.18.1 NAME 'c-PostOfficeBox'
SUP postOfficeBox COLLECTIVE )
3.9. Collective Physical Delivery Office Name
The c-PhysicalDeliveryOfficeName attribute type specifies a physical
delivery office name for a collection of entries.
( 2.5.4.19.1 NAME 'c-PhysicalDeliveryOfficeName'
SUP physicalDeliveryOfficeName COLLECTIVE )
3.10. Collective Telephone Number
The c-TelephoneNumber attribute type specifies a telephone number for
a collection of entries.
( 2.5.4.20.1 NAME 'c-TelephoneNumber'
SUP telephoneNumber COLLECTIVE )
3.11. Collective Telex Number
The c-TelexNumber attribute type specifies a telex number for a
collection of entries.
( 2.5.4.21.1 NAME 'c-TelexNumber'
SUP telexNumber COLLECTIVE )
3.13. Collective Facsimile Telephone Number
The c-FacsimileTelephoneNumber attribute type specifies a facsimile
telephone number for a collection of entries.
( 2.5.4.23.1 NAME 'c-FacsimileTelephoneNumber'
SUP facsimileTelephoneNumber COLLECTIVE )
3.14. Collective International ISDN Number
The c-InternationalISDNNumber attribute type specifies an
international ISDN number for a collection of entries.
( 2.5.4.25.1 NAME 'c-InternationalISDNNumber'
SUP internationalISDNNumber COLLECTIVE )
|